Видео

Thank you very much for sharing your wonderful thoughts

hello bro may i use this clip too ofc with credit thanx

I just replaced mine today and your video helped. Very informative. Thank you.

Sence you pulled the whole thing out, perhaps a cote of whatever on the whole thing would have been smart. Just saying. Good jod thx for the video,peace

Good job...best video i ve ever seen ..well explained !!

YOU, Sir are a SAINT! Thank you ever so kindly for taking the time & care to make this content & share it with people. Sending you BLESSINGS!

Very helpful video and clean truck!

My ball joint is on their so tight the bolt on this tool and the threads of the lower ball joint started bending 😢, had to give up after a few hours if alternating between this tool, smacking the thing with a sledge, and prying with a crow bar. Hooefully ill have better luck tomorrow

I have a Toyota Venza 2013. I tried this but my gas door still doesn't open. Is there a way to open it from the inside of my vehicle? I saw another video showing all Toyotas have another way to pull a plastic cord from the inside in the rear, but my car doesn't have that.

I installed everything the same way but when I went to put the radiator pins back in the pins went into nothing . But everything is on right

Back again to say thank you this video saved me . After you do it it’s a lot easier than it looks.. thanks again. For anyone who has a Cabrio .. I ended up have 4 bolts to take off on the radiator bracket . Great video

Amazing, thank you. You just saved me at least £100

nostalgia... man i wish i could go back to those times

noticed when you started the job fuel tank was under a quarter and it was full when done. good job.

I shut my car off . The fan never stopped spinning even after an hr of it cooling down . Was fine the last few times I seen it turn on and off. You think this is the Coolant sensor on the radiator failing ? I took my plug out and liquid came out

I just wanted to comment and express my sincere gratitude and thanks for you putting this video series together. My wife and I just finished her head gasket fix on her 99 4Runner and we couldn’t have done it without this. This series not only gave us the step by step process but the confidence to even attempt it ourselves. Out of all the videos on swapping head gaskets out there this is by far the best. An fyi for anyone out there looking to do this: there are slight differences between the engines and model years. Ours is a 99 and we noticed several places where our particular engine didn’t match up with the one in the video. It threw us off at first but quickly realized his was a 95 and ours is 4 years newer.

hows the gasket going to this point is the engine still running ? how many KMS/miles has it done then and now

Very good video thanks bro

Great video. I'm doing my 96 jetta this week and have the confidence now to do it.

Way better than a tornado

Excellent video thank you.

Clearest video explanation I can find on this.. thank you

“schools will remain open”

I love how almost 80% of replies on this video are solely concentrated on chair

How many miles did you have on this truck when the gasket/head was replaced?

Great videos. Why not remove the lower timing cover/crank pulley to make reinstalling the timing belt easier?

Is it a completely different switch on a 2003? I see nothing resembling this switch on mine.

The strangest thing about this ends up being that despite the heavy snowfall, the snowfall itself ends up being basically invisible. Gorgeous video though thank you for sharing!!

We got snow and freezing rain in Luxembourg causing dangerous conditions this winter❤

Your video was stolen and used in some silly ad about a mobile game being a snow blower guy

Link for the special tool????😂

Great video, rebuilt my Briggs and Stratton carb & now my lawnmower starts right up

Thanks for making this, its truly a great DIY video, easy to understand and easy fix. You helped and saved me a lot of time trying to figure this out.

Hey there! Could I also utilize your videos, giving proper credit?

Awesome video!!!!

As someone from the southern hemisphere, I've never lived anywhere it does have snow, I always feel heat and rain.

Going to do this with my son on his 02 Tacoma with 260k. Hope it goes half as smooth as yours. Great Video will probably be our bible/reference during the job.

I just replaced my entire suspension on my civic and THIS TOOL saved me! I did everything I could, even ALL the hammer tricks. Thank you for the upload!

Could the coolant have been laking from the exhaust manifold gasket? It has coolant chambers and fuel injection chambers, and maybe it mixed together there.

Hello Worse Than Chiggers! Can I use your video in my video plus comments to help people learn lessons so they can drive safer? I'll put your name on the screen, thank you for reading.

Ive got 4 O rings in the kit. One blue one which i can see where yours went but the other ones 2 are thicker and 1 thinner but appear the same diameter. Which goes where? Im trying to figure out which goes on the high pressure line. The thinner or thicker O ring

Why use a tool designed for a job when you are still going to use the good old hammer... pain dumb if u ask me

Thx again….

Harbor Freight has a press for sale too. Also, You're making your life too hard trying to get that bearing race off. Simply flip it over and take a torch to it, heating it up in just one spot and watch it fall down. When it does this, lift up the hub and let it fall the rest of the way off. Easy breezy.

Legendary

good lord, waaay too much work for such a minor problem lol. You're bound to cause more problems just trying to fix this not worth it!

Productive video!!

I remember this blizzard!! We got weeks off of school and I played outside with my dog for majority of the time <3

2024= owner just bought 2013 I have this problem. Thank you

Thank you!